NAME
    Test::NoWarnings - Make sure you didn't emit any warnings while testing

SYNOPSIS
    For scripts that have no plan

      use Test::More 'no_plan';
      use Test::NoWarnings;

    that's it, you don't need to do anything else

    For scripts that look like

      use Test::More tests => x;

    change to

      use Test::More tests => x + 1;
      use Test::NoWarnings;

    For scripts that use done_testing, use:

      use Test::More;
      use Test::NoWarnings 'had_no_warnings';

      ... # your actual tests

      had_no_warnings;
      done_testing;

DESCRIPTION
    In general, your tests shouldn't produce warnings. This modules causes
    any warnings to be captured and stored. It automatically adds an extra
    test that will run when your script ends to check that there were no
    warnings. If there were any warnings, the test will give a "not ok" and
    diagnostics of where, when and what the warning was, including a stack
    trace of what was going on when the it occurred.

    If some of your tests are supposed to produce warnings then you should
    be capturing and checking them with Test::Warn, that way
    Test::NoWarnings will not see them and so not complain.

    The test is run by an "END" block in Test::NoWarnings. It will not be
    run when any forked children exit.

USAGE
    Simply by using the module, you automatically get an extra test at the
    end of your script that checks that no warnings were emitted. So just
    stick

      use Test::NoWarnings;

    at the top of your script and continue as normal.

    If you want more control you can invoke the test manually at any time
    with "had_no_warnings".

    The warnings your test has generated so far are stored in an array. You
    can look inside and clear this whenever you want with "warnings()" and
    "clear_warnings", however, if you are doing this sort of thing then you
    probably want to use Test::Warn in combination with Test::NoWarnings.

    If you have a test script written using done_testing and no test plan,
    you have to call "had_no_warnings" before you call done_testing.

  use vs require
    You will almost always want to do

      use Test::NoWarnings;

    If you do a "require" rather than a "use", then there will be no
    automatic test at the end of your script.

  Output
    If warning is captured during your test then the details will output as
    part of the diagnostics. You will get:

    * the number and name of the test that was executed just before the
      warning (if no test had been executed these will be 0 and '')

    * the message passed to "warn",

    * a full dump of the stack when warn was called, courtesy of the "Carp"
      module

    By default, all warning messages will be emitted in one block at the end
    of your test script.

  The :early pragma
    One common complaint from people using Test::NoWarnings is that all of
    the warnings are emitted in one go at the end. While this is the safest
    and most correct time to emit these diagnostics, it can make debugging
    these warnings difficult.

    As of Test::NoWarnings 1.04 you can provide an experimental ":early"
    pragma when loading the module to force warnings to be thrown via diag
    at the time that they actually occur.

      use Test::NoWarnings ':early';

    As this will cause the diag to be emitted against the previous test and
    not the one in which the warning actually occurred it is recommended
    that the pragma be turned on only for debugging and left off when not
    needed.

FUNCTIONS
  had_no_warnings
    This checks that there have been warnings emitted by your test scripts.
    Usually you will not call this explicitly as it is called automatically
    when your script finishes.

  clear_warnings
    This will clear the array of warnings that have been captured. If the
    array is empty then a call to "had_no_warnings()" will produce a pass
    result.

  warnings
    This will return the array of warnings captured so far. Each element of
    this array is an object containing information about the warning. The
    following methods are available on these object.

    * $warn->getMessage

      Get the message that would been printed by the warning.

    * $warn->getCarp

      Get a stack trace of what was going on when the warning happened, this
      stack trace is just a string generated by the Carp module.

    * $warn->getTrace

      Get a stack trace object generated by the Devel::StackTrace module.
      This will return undef if Devel::StackTrace is not installed.

    * $warn->getTest

      Get the number of the test that executed before the warning was
      emitted.

    * $warn->getTestName

      Get the name of the test that executed before the warning was emitted.

PITFALLS
    When counting your tests for the plan, don't forget to include the test
    that runs automatically when your script ends.

    Checking for warnings is done using $SIG{__WARN__}. If other modules use
    this hook, it can interfere with this module's operation. For example,
    using the Carp::Always module will cause this module to always report no
    warnings.

SUPPORT
    Bugs should be reported via the CPAN bug tracker at

    <https://rt.cpan.org/Ticket/Create.html?Queue=Test-NoWarnings>

    For other issues, contact the author.

HISTORY
    This was previously known as Test::Warn::None

SEE ALSO
    Test::Builder, Test::Warn

AUTHORS
    Fergal Daly <fergal@esatclear.ie>

    Adam Kennedy <adamk@cpan.org>

COPYRIGHT
    Copyright 2003 - 2007 Fergal Daly.

    Some parts copyright 2010 - 2011 Adam Kennedy.

    This program is free software and comes with no warranty. It is
    distributed under the LGPL license

    See the file LICENSE included in this distribution or
    http://www.fsf.org/licenses/licenses.html.